Log in Register FAQ Memberlist Search pcHDTV Forum Index
pcHDTV Forum

pcHDTV Forum Index -> General pcHDTV topics -> Can Someone Please Comment on my lspci and dmesg Output?
Post new topic  This topic is locked: you cannot edit posts or make replies. View previous topic :: View next topic 
Can Someone Please Comment on my lspci and dmesg Output?
PostPosted: Sun Nov 14, 2004 5:48 pm Reply with quote
k7ar
 
Joined: 14 Nov 2004
Posts: 12




Can someone tell me if I have a problem or not? I have a MSI KT4V MB and it's not clear from reading the manual if the PCI slots are 2.2 compliant. I have properly compiled and installed the HD-3000 drivers and application software. I can get the tvtime NTSC tuner to work, but I don't get any signal strength at all for ATSC.

I would appreciate comments about my lspci output and dmesg output (shown below). Is it broke? And what the heck does "cx88atsc dvr error g" mean anyway? Maybe that's why the ATSC part doesn't work.

I appreciate any suggestions from the crowd, thanks!
Al Rovner

Output from lspci -v:
-----------------------

00:07.0 Multimedia video controller: Conexant Winfast TV2000 XP (rev 05)
Subsystem: Unknown device 7063:3000
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at de000000 (32-bit, non-prefetchable)
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

00:07.2 Multimedia controller: Conexant: Unknown device 8802 (rev 05)
Subsystem: Unknown device 7063:3000
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at df000000 (32-bit, non-prefetchable)
Capabilities: [4c] Power Management version 2


Segment from dmesg output:
---------------------------

cx88atsc dvr error g
cx88atsc dvr error g

cx8800[0]: AUD_STATUS: 0xf432 [mono/no pilot] ctl=BTSC_AUTO_STEREO
cx8800[0]: AUD_STATUS: 0xf4f2 [mono/no pilot] ctl=BTSC_AUTO_STEREO
View user's profile Send private message
Hope this helps.
PostPosted: Mon Nov 15, 2004 3:55 pm Reply with quote
Mapache
 
Joined: 14 Nov 2004
Posts: 2
Location: Maryland




I don't know about "cx88atsc dvr error g", but I get the same AUD_STATUS error from both of the HD-3000s cards in my system. Still, the cards work fine. Hear is what I get from dmesg and lspci.


lspci -v:
--------

Quote:
0000:00:0b.0 Multimedia video controller: Conexant Winfast TV2000 XP (rev 05)
Subsystem: Unknown device 7063:3000
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

0000:00:0b.2 Multimedia controller: Conexant: Unknown device 8802 (rev 05)
Subsystem: Unknown device 7063:3000
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at df000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2


dmesg:
-----
Quote:

cx2388x v4l2 driver version 0.0.4 loaded
cx8800[0]: found at 0000:00:0b.0, rev: 5, irq: 5, latency: 32, mmio: 0xde000000
cx8800[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV [card=14,autodetected]
cx88-video: Tuner type was unset
cx88-vidoe: Tuner type set to 46
attach: checking "cx8800[0]"
find by pci: checking "cx8800[0]"
cx8800[0]: i2c attach [client=eeprom]
cx8800[0]: i2c register ok
tuner: chip found at addr 0xc2 i2c-bus cx8800[0]
tuner: type set to 46 (Thomson DDT 7610 ATSC/NTSC)) by cx8800[0]
cx8800[0]: i2c attach [client=Thomson DDT 7610 ATSC/NTSC)]
cx8800[0]: registered device video0 [v4l2]
cx8800[0]: registered device vbi0
cx88: registered device dtv0
cx8800[0]: calling setmode
cx88atsc BTATSC_SetMode Rec Status 06 00
cx8800[0]: set_audio_standard_BTSC (status: known-good)
cx8800[0]: pcHDTV_HD3000 calling init_dvr
cx8800[0]: cx88: tvaudio thread started

cx8800[0]: AUD_STATUS: 0xe972 [mono/no pilot] ctl=BTSC_AUTO_STEREO
cx8800[0]: AUD_STATUS: 0xe6f2 [mono/no pilot] ctl=BTSC_AUTO_STEREO
View user's profile Send private message
Error G
PostPosted: Tue Nov 16, 2004 3:45 pm Reply with quote
SigTom
 
Joined: 11 Nov 2004
Posts: 26




I dont have this issue, but heres a topic about it:

http://pchdtv.com/forum/viewtopic.php?t=247
View user's profile Send private message
Can Someone Please Comment on my lspci and dmesg Output?
  pcHDTV Forum Index -> General pcHDTV topics
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 7 Hours  
Page 1 of 1  

  
  
 Post new topic  This topic is locked: you cannot edit posts or make replies.  


Powered by phpBB © 2001-2003 phpBB Group
Theme created by Vjacheslav Trushkin